the AT Command Set
Answering, and Hanging Up
Configuring with DIP Switches
Result Code Displays
and Configuring the Courier 56K Business Modem Remotely
Error Control, Data Compression, and Throughput
Querying and Help Screens
Line and Synchronous Applications
Meanings and Sets
V.25 bis Reference
Information and Limited Warranty
Courier 56K Business Modem Command Reference
This chapter contains information about:
Dial Security is designed to protect networks and data centres from unauthorised
You should be familiar with these terms before you continue:
|The device that is directly connected to the computer
you are using.
|The device at the other end of a telephone connection.
|The Courier 56K Business Modem that will be accessed
and controlled by other devices.
|The device that will access and control the host
Courier 56K Business Modem.
You can configure up to 10 accounts: one administrative account for you
and nine accounts for guest users. The account profiles are stored in
the host Courier 56K Business Modems nonvolatile random access memory
There are two forms of Dial Security; each will be explained later in
- Password Prompting
Setting up Dial Security
Here is a summary of the steps for setting up Dial Security:
- Set up an account for yourself
- Identify your account as the Administrative Account
- Set up guest-user accounts
- Enable local (host) security
- Choose a Dial Security method
- Enable Dial Security
- Activate the Dial Security settings
1. Set up an account for yourself
Use any of the 80 available accounts (numbered 0-79) for your account.
Use the AT%An command to set up user accounts.
Note: The AT%An command
is automatically written to NVRAM. It does not require you to send &W.
WARNING: Do not insert spaces between
commas or between fields and commas. Spaces will invalidate the command.
You can set the Courier 56K Business Modem to automatically dial back
a certain number after a client modem dials in.
Note: Count your commas. There
should always be at least four commas in the %A command. Do not
insert spaces between commas or between fields and commas. Spaces will
invalidate the command.
To make the host Courier 56K
|Hang up and then dial back a guest device
at a specified number.
Expect a pause of approximately 1.5 minutes before the modem dials
back. You cannot alter the duration of the pause.
area code and phone number
|Prompt you to enter a number at which
to dial back a device, and then have the Courier 56K Business Modem
dial back the device at that number
Note: To enable Dialback, you must
enable Dial Security with Prompting. See step 6.
2. Identify your account as the Administrative Account
For your modem to
|Identify your account as the Administrative
This example sets account 0 as the Administrative
Once you set the administrative password, you cannot view or modify
the guest account profiles unless you enter the correct administrative
WARNING: Be sure to remember your
administrative password. If you enable Dial Security and then forget
your administrative password, you will be locked out of the Courier 56K Business Modems dial security features. You will need to restore
the factory defaults by setting DIP switch 10 ON. This will erase ALL
passwords and you will have to reconfigure all your accounts.
3. Set up guest-user accounts
Use the AT%An command to set up guest-user accounts in the same way
you set up your administrative account. You can set up nine guest accounts.
Refer to the figure in step 1 regarding information about formatting
the AT%An command.
After you have enabled the guest accounts, make sure the guest users
know their passwords and the log-in procedure.
4. Modifying Accounts
After you have set up an account, you can modify each field independently.
If a field is to remain unchanged from its original setting, just insert
a comma as shown:
The command above allows the guest user to supply a dialback number
that is different from the one stored in the original account record.
Enable Local Security.
WARNING: If you do not enable Local
Security, the Dial Security settings will not be protected and other
users will be able to change or erase them.
For your modem to
|Protect the administrative password (local security
Note: You must use the &W
command to save the settings in NVRAM. If you dont, the next time
you reset or power off the Courier 56K Business Modem, Dial Security
will be disabled.
5. Decide which Dial Security option to use
You can choose from the two types of Dial Security: Autopass and Password
Autopass is the default form of password protection. Autopass automates
the process of logging in to the host modem, but it requires the guest
and host devices to be USRobotics Courier modems.
When a guest device attempts an Autopass connection, the guest includes
the password in its V.42 error-control request. The host modem checks
all the enabled passwords in its security accounts for a match.
Password Prompting allows connections with any guest device, as long
as the guest user knows the correct password.
When the host has Password Prompting enabled, it asks guest users for
a password. The host modem checks the received password against each
of its active Security accounts.
Note: There is no Password Prompting
capability in synchronous mode.
The table below is a comparison between Autopass and Password prompting.
When using Autopass Prompting
When using Password Prompting
|Both the host and guest devices are made
by USRobotics and have Dial Security enabled.
||Guest devices dont have to support
USRobotics Dial Security.
The connection between the Courier 56K Business
Modem or modems is under V.42 error control.
(Refer to the Alphabetic Command Summary chapter
of the Appendixes section for information about using AT&M4
|V.42 error-control connections arent
|If the guest includes an invalid password,
the host sends an INVALID PASSWORD message and hangs up.
If the guest sends an invalid password, the host
prompts twice more before disconnecting.
If the guest does not send a password after 60 seconds,
the host disconnects.
|If the guest includes a valid password,
the host permits a secure connection.
||The host will still always respond to
a correct Autopass attempt.
|If the guest did not enable Dial Security,
the host will not accept the call unless prompting is enabled on the
host Courier 56K Business Modem.
6. Enable Dial Security
WARNING: Before you enable Dial
Security, you must set up an administrative account and password. See
Steps 1 & 2.
For your modem to enable
|Autopass Dial Security
|Dial Security with Password Prompting (this also
|Dialback Security, enable Password Prompting and
enable Dialback in each guest account
where n is the account number. See the figure in
previous section, Setting Up Dial Security for more information.
Example: Issuing AT%A3=wombat,y,y,y,5551234 to your modem will
enable Password Prompting and Dialback for account 3, which has the
Note: You must use the &W command
to save the settings for Enabling Autopass Dial Security and Dial Security
with Password Prompting. If you dont, the next time you reset
or power off the Courier 56K Business Modem, Dial Security will be disabled.
If you need a reference when setting these commands, you can use the
ATI10 command. Refer to the Alphabetic Command Summary chapter of the
Appendixes section for more information about the ATI10 command.
7. Send ATZ or ATZ! to activate the Dial Security settings.
Note: Make sure that DIP switch
10 is OFF, so the modem loads the settings stored in NVRAM. If DIP switch
10 is ON, the settings in ROM (&F0) are loaded, disabling dial security.
You can retrieve the dial security settings by setting DIP switch 10
OFF and resetting the Courier 56K Business Modem using ATZ or by toggling
the power of the modem.
Maintaining Security Accounts
Once the administrative password is set and Dial Security is enabled,
the administrator is the only one who can access account information.
You can use the AT%S= and AT%E= commands to change and modify account
|For your modem to
|Access accounts by disabling local security
View account information, once access has been granted.
Remote users may only use this command during remote
access sessions if local-access security is disabled.
|Erase local-access password
|Erase Autopass password
|Erase passwords in accounts 0-79
|Erase phone numbers in accounts 0-79
|Disable Account, Dialback, and New Number fields
in accounts 0-79.
|Edit or overwrite an individual account or an individual
where n is the account number.
See the image in the Setting Up Dial Security section for more information.
Example: Sending AT%E=3 erases passwords for accounts 0-79.
Note: When using the AT%S= command,
the device echoes the administrative password, which is case-sensitive.
Courier 56K Business Modems will accept an invalid password entry, but
will lock out users from the security commands. For example, if the password
is Green, but you enter GREEN, an OK is displayed. However, if you try
to type a security command (for example, ATI10 to view accounts), an [ACCESS
DENIED] message is displayed.
Dial Security accounts may be configured remotely. (Refer to Configuring
Dial Security Remotely at the end of this chapter.)
What The Guest User Needs To Do
When guest users want to call in to the host (assuming you have enabled
Dial Security by entering ATS53.0=1),
- They must know the password.
- If you have enabled Dialback, they must set their device to auto-answer.
- If the host has security enabled, get a password from the hosts
administrator. The password is case-sensitive, so be sure to copy it
If the host has prompting enabled and the host operator enables Dialback
for your account, skip to Step 3.
- For guest users with Courier 56K Business Modems (or I-Modems) only:
a) Create a security account using the password the hosts
administrator asked you to use. (See Setting Up Dial Security, earlier
in this chapter, for instructions.)
b) You need to assign the password as your Autopass password.
For your modem to
|Assign the password as your Autopass
where n is the number of the account you set up.
Example: Sending AT%V=PW3 will assign the password as an
Autopass password for account 3.
c) Check to see that you set your Autopass password correctly
by using the ATI10 command.
Your Autopass password appears beside AUTOPASS PASSWORD if you have
done all the steps correctly.
d) Once the Autopass password is set, enable your Courier 56K
Business Modems Dial Security.
For your modem to
|Enable Dial Security
CAUTION: If you do not follow
an S-Register setting with &W, the setting will be retained only
until the next reset or power off.
- If Dialback is enabled at the host Courier 56K Business Modems
site, set your modem to answer the host Courier 56K Business Modem when
it dials back.
For your modem to
|To answer the Dialback call
Call the host.
After the call ends you can disable Auto Answer.
For your modem to
|Disable Auto Answer
Configuring Dial Security Remotely
The host administrator can configure the hosts security
Note: At the host device, you must
have previously enabled remote access and assigned a remote-access password
that allows view-and-change privileges (Refer to the Accessing
and Configuring the Courier 56K Business Modem Remotely appendix in this guide). You
may want to use your administrative password as your remote-access password.
Dialing In From the Remote Site
- From the remote site, connect to the host using Dial Security. Once
a connection is made, follow the instructions for beginning a remote-access
session as described in the Accessing
and Configuring the Courier 56K Business Modem Remotely appendix in this guide.
- When remote access has been granted, use the AT%S= command to access
the Dial Security accounts. Refer to the Maintaining Security Accounts
section in this chapter.
To view the security account information use ATI10.
- Make any configuration changes and execute them immediately by entering
- To end the remote session and reactivate Dial Security on the host,
reset the host device by issuing ATZ.
WARNING: If you do not use the ATZ
command to end a remote-access session, Dial Security will remain disabled
at the host, and anyone dialing in to the host for remote access will
have access to the ATI10 screen and all Dial Security accounts.
DTMF (Dual Tone Multi-Frequency) Security requires a modem to go off hook
when it receives a call but keep silent until it receives the valid DTMF
password. After the modem receives the valid password, it will begin training.
If the DTMF password is invalid, the modem will go on hook, and the DTE
will never know there had been a call coming.
The DTMF security status and password are shown in the ati10
DTMF security is enabled by setting the S53 bit 3, e.g.
S53=8 or S53.3=1.
Using the %D command sets the DTMF security password (AT%D=PWn,
n=0--39). Make sure to disable that account so no one can use the DTMF
password as the Dial Security account. For example, to set local modem
DTMF security password, you may use following command: AT%A0=123456,N,,,
then AT%D=PW0. You can change that security account later, if you like.
The DTMF password can be the combination of 0123456789*ABCD;
the # is used as the password end sign. The maximum length of the DTMF
password is eight characters.
The remote modem dial string should look like this: ATDT2625000@123456#.
In this example, 123456 is the DTMF security password.